P938E Engine Trouble Code

When you check engine light came on code P938E the reason should be . However your vehicle's manufacturer may have a different definition for the P938E OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

When the DTC check engine light comes P938E code on the first you can check is the gas related maybe gas cap. Pull over, retighten it, and take a look at the cap to see if it has any cracks inside. Go on driving and to see if the check engine light turns off automaticly. On the other hand, you can buy a gas cap for about $4.5 at an auto parts store. All you need to do is take the old one take off and take on the new one. If you've already bought it to the store, you might as well just replace the cap. While not car-threatening, it's good to take care of this right away to improve gas mileage/km.

P938E Code Meaning :

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P938E OBD-II Diagnostic Powertrain (P) Trouble Code Description

P938E engine trouble code is about Engine Shutoff Solenoid Malfunction. Fuel Rail Pressure Sensor Circuit Malfunction and Cylinder 1 Injector Circuit Low causes most of code P938E.

Reason For P938E Code

The reason of P938E OBD-II Engine Trouble Code is Fuel Rail Pressure Sensor Circuit Malfunction.

P938E DTC reports a sensor fault, replacement of the sensor is unlikely to resolve the underlying problem. The engine error is most likely to be caused by the systems that the sensor is monitoring, but might even be caused by the wiring to the sensor itself.

How To Repair P938E Code

Before starting let's see P938E repairing process steps:

• Qualified technicians will begin by using a scan tool to access P938E code stored in the ECU.
• Technicians will note P938E code present and any freeze frame data associated with them.
• After all, if you sure the engine trouble is finished, the code will be cleared.

The reductant injector is part of the system that reduces the gas that is expelled through either the catalytic converter in gas engines, or the particulate filter in diesel engines. There are sensors in the exhaust system, used by the reductant injector to input voltage readings to the PCM.

If you suspect that your car has a defective mass air flow sensor, bring it to a certified mechanic so that a whole computer diagnostic can be run. In most situations, a defective mass flow sensor has a certain code that will process throughout computer diagnostics, and is normally simple to check into with computer testing equipment.

Sometimes P938E code comes with P938E00 code.

Diagnosis Of Engine Error OBD Code P938E

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P938E trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P938E code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.